Pheonix

Pheonix Garage Door Repair Experts

A garage door is one of the most basic, yet most important requirements of your everyday life. When you get ready for your office and open the door to your garage with just a flick of your garage gate opener remote, you never realize what an essential tool it is. However, when something goes wrong with your garage gate opener and you have no option of getting to your car, and you are getting late to your office, you realize how important it is to your daily life. Thus, when your garage gate begins to malfunction, it is important that you perform the garage door repair at the soonest.

Repairing a garage entrance is not very hard and you can perform the repairs yourself if you are good with tools. However, if you are not too sure of yourself, do not attempt to do the garage entrance repair yourself, as you could hurt yourself.

What are the various problems that you can face with your garage door?

o Does not respond to the opener remote at all

o The garage gate opener runs, but does not work

o The garage gate opens and closes partially

o You need to work hard to get the door to open

If you are facing any of these problems, you shall have to start away with the garage door repair in Pheonix right now.

The Pheonix garage door repair usually involves some testing of the condition of the motors, replacing the batteries of the garage gate opener, lubricating the machinery, as well as aligning the machine in the right manner.

roll up garage doors

Before beginning the repair works, you should check the power supply, because you need continuous power supply to check if your garage entrance is working right. Next, you need to find out the system on which your garage door works. There are two types of spring system openers. The standard extension garage gate is easiest to repair. If this is the type of garage gate you have, check for broken cables and pulleys as well as broken springs and rollers.

If your system used a torsion spring, you need to call in a professional. This is because such a garage entrance opener is large and mounted over the door and you may hurt yourself while trying to perform the garage door repair.

If you require a temporary fix for your garage entrance opener, you should use the red cord that hangs from your opener. Pulling this cord will disconnect the opener from the door and now you can manually open the door. If however, the spring of the opener is broken, the door might shut suddenly, so be careful to keep your children or pets away from the door when you are carrying out the garage door repair.

If however you feel that the problem lies with the garage door tracks and not with the opener, you may call the manufacturer for a replacement of the garage door parts. Take care to read the manufacturer’s guide properly, so that you can repair the doors with ease.

Why Replace the Garage Door Opener

Genie garage door systems are a common system that people have in their garage. Just like any other system, things break such as the springs, door panels, and overhead motor. The truth is that in order to fix these systems, you have to do exactly the same thing as other generic garage door openers.

The first thing to do when you are looking to repair a system is to evaluate what is wrong. Are the springs damaged? Is the door itself off of it's guide tracks? Does the overhead motor turn on when you press the button? By determining the initial problem, you will save yourself a lot of time.

If the motor turns on when you press the button, chances are you just need to replace the sprocket, which can be purchased at any hardware store. If the springs, or motor have broken and don't run, we would suggest hiring a professional to help you make the repairs. The reason for this is because the springs are extremely dangerous if not handled correctly. Every year people make the mistakes with garage springs, and every year people die from spring accidents.

Motor replacement is quite simple as you can go to most warehouse stores and purchase a new overhead motor. The nice thing about this type of repair is that you literally just have to swap out the motor and not worry about any other hardware. Make sure the garage chain has the proper amount of slack and is not too tight. If the chain is too tight it will strip the sprocket of the teeth.

garage door opener

Have you grown tired of that rusty or rotted garage door that never seems to work quite the way it should? If you're in need of some serious repair or maintenance, but don't want to pay a professional to do the work for you, then perhaps you can do the work on your own. Installing a new system on your own is definitely possible and only requires a few tools and the right knowledge. Within a few hours you can give a brand new look to your home.

The following steps will provide you with the basics of installing a pre-hung garage door. Remember, it's important that you maintain safety while performing this task, and always consult the instruction manual if any questions ever arise.

Position The Bottom Panel In The Doorway

Install weatherstripping on the bottom panel and position the panel in the doorway. Temporarily hold the panel in place by tapping nails through either side of the panel brackets into the door jamb. When the panel is in place, attach hinges to the upper edge of the panel.

Install The Tracks

After locating the first panel in the proper place, install the tracks for the garage door according to the instructions which should be found in the instruction manual.

Install Rollers

When the tracks have been set in place, install the rollers and any remaining brackets that either are to be installed onto the door itself or the wall frame, so that the door panels may be set into place.

Install The 1st Panel

Position one side of the panel into the tracks, and do the same for the other side.

Install The 2nd Panel

Prepare the second garage door panel by installing the rollers where necessary. When ready, lift the panel into place and insert the rollers into the tracks. You will want to get help from another person for this step.

Install the 3rd Panel

Prepare the third panel by installing the rollers as well as any brackets that are needed. Lift the panel into place and insert the rollers for this panel into the tracks. When the panel is in place, make sure the vertical tracks are fully fastened to the garage wall using lag bolts that are provided with the package At this point, make sure the door is level and the tracks are plumb.

Attach Jamb Brackets

Attach the jamb brackets and fasten them to the wall, ensuring that the lag screws are drilled into the solid framing boards for security.

Install Top Tracks

Install the curved and horizontal portions of the tracks according to the specifications set forth in the user manual. Be sure to rest the horizontal tracks on top of something so they do not swing free or fall down.

Install The Track Hanger

Check to see that the horizontal track is completely level. Attach the hanger mounting bracket to the ceiling in a solid position where the lag screws can be drilled into framing boards. Install one end of the hanger to the mounting bracket and then line up the hanger with the horizontal garage door track. Trim the hanger and then fasten the horizontal track to the hanger. Repeat this process on the other side with the other horizontal track section.

Install The Last Door Panel

When the horizontal track sections are in place, install the final door panel.

Install Torque Tube Or Tension Springs

If the garage door you are installing comes with a torque tube, you can install it according to the manufacturer specifications. If your garage door uses tension springs, you may need to call a professional because special tools are required to obtain the proper tension. Improperly installed springs can be a safety hazard for both property and people. When in doubt, call the professional.

If you have the right tools and the knowledge to complete the task, you can install that new system and give your home a new face lift.


Home Page